PLANTER

A cedar planter box with the gaps counted.

Two courses of 1×6, a slatted floor, and posts that stand on the floor so they do not need notches. Written for dry cedar.

A cedar box, 18 inches long, 12 inches wide, and 11 inches tall on the outside. The walls are two courses of 1×6. The floor is four 1×4s with 1/2 inch gaps. Corner posts are 2×2s that stand on the floor, so they never have to be notched around it. It is a planter for a deck or a step, not a raised bed you can sit on.

Buy dry cedar if you can, stamped S-DRY or KD. Those are the PS 20 marks for lumber surfaced at 19 percent moisture or less. A dry 1×6 is at least 3/4 by 5-1/2, and two of them stack to 11 inches with nothing left over. Green western red cedar is a different width. The size chart is on the nominal and dressed sizes page.

Cut list

Lengths are finished. Widths are PS 20 minimum dressed dry sizes. Measure green cedar before you cut.
PartQtyStockLength
Long wall slat41×618
Short wall slat41×610-1/2
Corner post42×28-3/4
Floor cleat21×216-1/2
Floor board41×4about 10-1/2

Floor-gap check: the inside length is 16-1/2. Four dressed 1×4s are 14 inches. The remaining 2-1/2 inches divided by five gaps is 1/2 inch each. Post-height check: an 11 inch wall minus a 1-1/2 inch cleat minus a 3/4 inch floor is 8-3/4.

What to buy

  • Two 1×6 × 8 foot cedar boards. One takes three 18 inch slats and two 10-1/2 inch slats. The other takes the remaining 18 and two 10-1/2s.
  • One 1×4 × 4 foot board for the floor. Four 10-1/2 inch pieces plus kerfs fit in 48 inches.
  • One 1×2 × 4 foot board for the cleats, and one 2×2 × 4 foot for the posts. Four 8-3/4 inch posts fit in 48 inches.
  • Exterior waterproof glue, 1-5/8 inch and 1-1/4 inch stainless or coated screws, and a piece of landscape fabric.

Nominal board feet of those sticks, using the lengths you buy: two 1×6 × 8 foot boards are 8 board feet, the 1×4 × 4 is 1.33, the 1×2 × 4 is 0.67, and the 2×2 × 4 is 1.33. That is the tally, not the volume left after the offcuts. The board-foot calculator will take a price per board foot or a price per stick.

Build it

  1. 1
    Cut the walls Cut four long slats at 18 inches and four short slats at 10-1/2 inches. Two courses of a 5-1/2 inch dressed 1×6 stack to 11 inches. The short slat is 12 minus two 3/4 inch walls.
  2. 2
    Cut posts, cleats, and the floor Cut four posts at 8-3/4 inches from 2×2, two cleats at 16-1/2 inches from 1×2, and four floor boards from 1×4 at the inside width. That width is 10-1/2 if the walls are 3/4. Trim the floor boards until they drop in.
  3. 3
    Screw the cleats and the floor Screw a cleat inside each long wall, flush with the bottom edge, with 1-1/4 inch exterior screws. Set the four floor boards on the cleats. Four boards at 3-1/2 inches use 14 inches of the 16-1/2 inch inside length, which leaves 2-1/2 inches. Split that into five gaps of 1/2 inch: one at each end and one between boards. One screw each end of each floor board is enough. You will replace them someday.
  4. 4
    Add the posts and the walls Stand each post on the floor in a corner. The post is 8-3/4, and the cleat plus the floor is 2-1/4, so the post ends flush with the top of the 11 inch wall. Screw the long slats to the posts from the outside with 1-5/8 inch stainless or coated screws, two per post. Then fit the short slats between the long slats and screw them to the posts the same way.
  5. 5
    Drainage and a liner Lay landscape fabric over the gaps so the potting mix stays in the box. Do not seal the bottom. For vegetables, read the Maryland extension page linked below before you switch this plan to pressure-treated lumber. Cedar is on that page's decay-resistant list. A heavy plastic liner with holes punched in it is the barrier they describe.

Safety

Wear safety glasses. Wear hearing protection with a power saw, and a dust mask when you sand. Keep fingers out of the cut line and use a push stick on a table saw. Unplug a saw before you change the blade. Predrill pine and cedar so the screws don't split the board.

These are shop notes for a home project, not a substitute for the manual that came with your saw. OSHA's woodworking overview is the longer version for anyone cutting wood as a job.

Do not sit or stand on the box. The butt joints and the posts are there to hold soil, not a person. Set the planter on feet or bricks if the deck stays wet. Cedar still decays, just more slowly than pine. Nothing in this cut list makes it permanent.

Questions

Can I build this from pine?

The cuts work in pine. Pine rots outdoors. This plan is written for cedar. If the stamp says S-GRN, the board may not be the dry 3/4 by 5-1/2 size. PS 20 Table 5 gives western red cedar its own green widths. Measure green cedar. Do not trust the dry column.

How big is the soil opening?

Inside length is 16-1/2 inches and inside width is 10-1/2 inches, before the posts. The posts are 1-1/2 inch squares in the corners, standing on the floor. The walls hang 1-1/2 inches below the floor, which is the cleat, so the floor is not sitting in a puddle.

Where TimberTinker fits. The species the listing names are walnut, maple, oak, cherry, and pine. Cedar is not in that list, so the app will not show you this planter in cedar. Use it to check the cut list and the cost in pine or oak, then buy cedar for the real box if it will live outside. TimberTinker: Woodworking 3D is free to download on the U.S. App Store. The listing says the first 3 projects are free, then Premium. On the U.S. listing checked November 19, 2026, the in-app purchases are named Unlimited Access at $5.99, Unlimited Access at $12.99, and timbertinker at $49.99. The listing does not say how long each purchase lasts. It does say the app uses real lumber sizes from 2×4s to 3/4 inch plywood, writes a cut list, and estimates cost by the board foot and by the sheet. Redraw this piece in the app and read its cut list as a second check. Measure the board in your hand before you cut. This page has not compared the app's output to these numbers.

Sources

Pages and prices were checked November 19, 2026. A store price can change, and a support page can be revised. The link is the record.