A standing bench, 48 inches long, 24 inches deep, and 34 inches high, from four 8-foot 2×4s and one sheet of 3/4 inch plywood. The base is 48 by 20. The top hangs 2 inches past the base at the front and the back, which gives a clamp somewhere to land. The lower shelf sits on stretchers 6 inches off the floor.
Leg length is 33-1/4 only when the top is 3/4 inch. A sheet sold as 3/4 inch plywood is often stamped 23/32. Measure the panel and change the legs if you care about hitting 34 inches exactly. The nominal board-foot tally of the four 2×4s is 21.33. Plywood is sold by the sheet, not by that tally. Run the numbers in the board-foot calculator.
Cut list
| Part | Qty | Material | Length |
|---|---|---|---|
| Leg | 4 | 2×4 | 33-1/4 |
| Long apron and long lower stretcher | 4 | 2×4 | 45 |
| Short apron and short lower stretcher | 4 | 2×4 | 13 |
| Top | 1 | 3/4 plywood | 24 × 48 |
| Shelf | 1 | 3/4 plywood | just under 45 × 16 |
Length check: 1-1/2 + 45 + 1-1/2 = 48. Depth check: 3-1/2 + 13 + 3-1/2 = 20. The lower stretchers sit on the inner 1-1/2 inches of the legs, so a 16 inch shelf can rest on the front stretcher and the back stretcher and still pass between the legs. The short stretchers fill the 13 inch opening between the front ladder and the back ladder and hold the ends of the shelf.
What to buy
- Four 2×4 × 8 foot studs. Two boards each take two 45 inch rails (90-1/8 inches with one kerf). The other two boards each take two 33-1/4 inch legs and two 13 inch rails (92-7/8 inches with three kerfs). If a stud is short of 96 inches, buy a fifth.
- One 4×8 sheet of sanded 3/4 inch plywood. The top and the shelf both come out of it. Georgia-Pacific's Plytanium sanded panels, which cite PS 1-22, list a 4-foot or 8-foot size as plus 0, minus 1/16 inch, so a stated 4×8 can measure 47-7/8 by 95-7/8. Cut the top from the panel you have. Do not assume the factory edge is exactly 48.
- Wood glue, a box of 3 inch construction screws, 2 inch screws for the top, 1-1/2 inch screws for the shelf, and either a pocket-hole jig or eight 2 inch L-brackets with 1 inch screws.
Build it
- 1Cut the 2×4s From four 8-foot 2×4s cut four legs at 33-1/4, two long aprons and two long lower stretchers at 45, and two short aprons and two short stretchers at 13. Confirm each 8-foot board is a full 96 inches before you use the tight layout below.
- 2Build the front and back ladders Stand each leg so the 3-1/2 inch face runs front to back. The narrow 1-1/2 inch face is what you see from the front of the bench. Make two ladders, a front and a back. The 45 inch apron goes between the legs on the outside face, flush with the front of the legs and flush with their tops. The 45 inch lower stretcher also runs between the legs, but slide it to the inner corner: its back edge flush with the back edge of the front legs, so it covers the inner 1-1/2 inches of the 3-1/2 inch depth. The top of that stretcher is 6 inches off the floor. Glue both rails. Two 3 inch screws through each leg into each rail end. Predrill the leg. A 3 inch screw through the 1-1/2 inch leg leaves 1-1/2 inches in the rail.
- 3Join the ladders Stand the ladders so the outside depth is 20 inches. The math is 3-1/2 plus 13 plus 3-1/2. Fit a 13 inch short apron at each end, flush with the top, and a 13 inch short stretcher at each end with its top 6 inches up. Those short rails land on the wide inner face of the legs. Fasten them with a pocket-hole jig set for 1-1/2 inch stock, using the screw length that jig's chart gives for 1-1/2 inch material, or with two 2 inch L-brackets and 1 inch screws per joint, plus glue.
- 4Square the base and add the top Measure the two diagonals across the top of the base and push until they match. Cut the top to 24 by 48. Center it so the ends are flush and about 2 inches hangs over the front and the back. Screw down through the top into the aprons with 2 inch screws, about every 8 inches, centered on the 1-1/2 inch edge of each apron. If the plywood does not measure 3/4 inch thick, recut the legs so leg plus the thickness you measured equals 34 inches.
- 5Drop in the shelf Cut the shelf a hair under 45 inches long and 16 inches deep. Set the front edge on the front lower stretcher and the back edge on the back lower stretcher. You want at least 3/4 inch of the shelf sitting on each of those stretchers. The two short lower stretchers hold the ends. Screw it down with 1-1/2 inch screws so it cannot slide. It is a shelf for hand tools, not a place to stand.
The long rails are the easy joints: the screw passes through 1-1/2 inches of leg and still has 1-1/2 inches of thread in the rail. The short rails meet the wide face of the leg. A screw started from the outside would have to travel through 3-1/2 inches of leg before it reached them, which is why those four joints use pocket screws or brackets instead.
Safety
Wear safety glasses. Wear hearing protection with a power saw, and a dust mask when you sand. Keep fingers out of the cut line and use a push stick on a table saw. Unplug a saw before you change the blade. Predrill pine and cedar so the screws don't split the board.
These are shop notes for a home project, not a substitute for the manual that came with your saw. OSHA's woodworking overview is the longer version for anyone cutting wood as a job.
A 2×4 bench is for the shop. Check that no screw tip comes through a face you will lean on. Set it on a flat floor. If it rocks, shorten the long leg. Do not fix a rock by shimming one corner and then calling it square.
Questions
How tall is the bench?
34 inches when the top is 3/4 inch thick and the legs are 33-1/4. Change every leg by the same amount if you want a different height. Keep the top thickness in the sum.
What is the bench for?
Assembly, sanding, glue-ups, and a small drill. The top overhangs 2 inches at the front so a clamp can grab it. It is not a vise bench for heavy hand planing, and this page does not give it a weight rating.
Sources
- NIST PS 20-25. Table 3, dry 2×4 minimum dressed size 1-1/2 by 3-1/2. Section 2.2, board measure.
- Georgia-Pacific Plytanium sanded plywood. Length and width tolerance +0, −1/16 inch on a 4-foot or 8-foot size, citing PS 1-22. 23/32 category thickness listed at 0.703 inch for the sanded panel.
- APA – The Engineered Wood Association, plywood. Plywood is graded and sold as a panel. Thickness on a structural panel is a performance category, often 23/32 where a shelf tag says 3/4.
- TimberTinker App Store listing. Workbenches template, sheet-good sizes through 3/4 inch plywood, sheet layout, and board-foot cost.
- OSHA woodworking. Hazard overview.
Pages and prices were checked November 19, 2026. A store price can change, and a support page can be revised. The link is the record.