STEP STOOL

A one-step stool from a 2×12.

16 wide, 11-1/4 deep, 10 tall. The cleat, the overhang, and the stretcher length are spelled out so the screws are not in end grain alone.

A one-step stool, 16 inches wide, 11-1/4 inches deep, and 10 inches high. The tread and the legs come from one 4-foot 2×12. A 2×2 cleat under each end of the tread carries the load in face grain, and a 2×4 stretcher keeps the legs from walking apart. There is no handle. It is a step, not a ladder.

A dry 2×12 is at least 1-1/2 by 11-1/4 under PS 20 Table 3. The nominal tally of the 2×12 × 4 foot board is 8 board feet. The short 2×2 and the short 2×4 add a little more than that if you have to buy a full stick. Price it with the board-foot calculator.

Cut list

Finished lengths. The 2×12 and 2×4 sizes are PS 20 minimum dressed dry sizes.
PartQtyStockLength
Tread12×1216
Leg22×128-1/2
Cleat22×28
Stretcher12×411

Height check: 8-1/2 + 1-1/2 = 10. The footprint of the legs is wider than the stool is tall: the outer faces of the legs are 14 inches apart, and the step is 11-1/4 deep. Stand in the middle.

What to buy

  • One 2×12 × 4 foot board. The tread and two legs use 33 inches plus two kerfs, about 33-1/4, which fits in 48.
  • One 2×2 × 2 foot board for the cleats, and one 2×4 × 2 foot board, or an offcut, for the 11 inch stretcher.
  • Wood glue, 2-1/2 inch screws, and 3 inch screws.

Build it

  1. 1
    Cut the 2×12 From a 4-foot 2×12 cut the tread at 16 inches and two legs at 8-1/2. The dressed 2×12 is 1-1/2 by 11-1/4, so the step is 11-1/4 deep and the legs are the full depth of the board. 8-1/2 plus the 1-1/2 tread is 10 inches tall.
  2. 2
    Add a cleat inside each leg Glue an 8 inch 2×2 cleat to the inside face of each leg, flush with the top, and inset so it does not stick past the 11-1/4 depth. Four 2-1/2 inch screws through the cleat into the leg. The screw stops inside the 1-1/2 inch leg.
  3. 3
    Set the tread The space between the legs is 11 inches, which is 16 minus two 1 inch overhangs minus two 1-1/2 inch legs. Glue the top of each leg and each cleat. Set the tread on. Screw down into the cleats with 2-1/2 inch screws. That leaves 1 inch of thread in the cleat and does not come out the bottom.
  4. 4
    Tie the legs Cut a 2×4 stretcher at 11 inches. Set the bottom of it 2 inches above the floor. Glue, and drive two 3 inch screws through each leg into the end of the stretcher. This is the piece that keeps the legs from spreading when you step up.

Safety

Wear safety glasses. Wear hearing protection with a power saw, and a dust mask when you sand. Keep fingers out of the cut line and use a push stick on a table saw. Unplug a saw before you change the blade. Predrill pine and cedar so the screws don't split the board.

These are shop notes for a home project, not a substitute for the manual that came with your saw. OSHA's woodworking overview is the longer version for anyone cutting wood as a job.

Put the stool on a flat floor. One person. Do not use it on a counter to reach a ceiling, and do not let a child climb it. If it rocks, the floor is the problem or a leg is long. Shorten the long leg. Do not put a pad under one side and then step on it.

Questions

How much weight will it hold?

This page does not give a weight rating. The tread sits on the leg tops and on cleats screwed into face grain, and a stretcher keeps the legs from spreading. Use it as one step for one adult, on a flat floor, with your foot between the legs rather than on the 1 inch overhang. It is not a ladder and it has no handle.

Why not screw the tread only into the ends of the legs?

Screws into end grain pull out. The cleat is face-screwed to the leg, and the tread is face-screwed to the cleat. The glue on the leg top keeps the leg from shifting. Skip the cleat and the step is a weaker stool.

Where TimberTinker fits. A step stool is small enough to be one of the three free projects. The listing's joinery list includes pocket screws and dowels if you would rather not use the face screws on the cleat. TimberTinker: Woodworking 3D is free to download on the U.S. App Store. The listing says the first 3 projects are free, then Premium. On the U.S. listing checked November 19, 2026, the in-app purchases are named Unlimited Access at $5.99, Unlimited Access at $12.99, and timbertinker at $49.99. The listing does not say how long each purchase lasts. It does say the app uses real lumber sizes from 2×4s to 3/4 inch plywood, writes a cut list, and estimates cost by the board foot and by the sheet. Redraw this piece in the app and read its cut list as a second check. Measure the board in your hand before you cut. This page has not compared the app's output to these numbers.

Sources

  • NIST PS 20-25. Table 3. A dry nominal 2 inch board is at least 1-1/2 thick. A dry nominal 12 inch width is at least 11-1/4. A dry 2×4 is at least 1-1/2 by 3-1/2. A dry 2×2 is at least 1-1/2 by 1-1/2.
  • TimberTinker App Store listing. Three free projects, then Premium. Pocket screws and dowels are in the joinery list.
  • OSHA woodworking. Hazard overview.

Pages and prices were checked November 19, 2026. A store price can change, and a support page can be revised. The link is the record.