BOOKSHELF

Simple bookshelf plans, with the cut list checked.

A 30 by 36 inch pine bookcase from two 8-foot 1×10s. Openings, screw lengths, and the board-foot tally are calculated on the page.

This is a three-shelf pine bookcase joined with glue and screws. No dados, no face frame. Finished size: 30 inches wide, 36 inches tall, 9-1/4 inches deep. The two openings are equal, 16-7/8 inches each. It is a first case for paperbacks and small objects, built from two 8-foot 1×10s and a piece of 1/4 inch plywood.

Every length below is a finished length. Dressed size comes from NIST Voluntary Product Standard PS 20-25, Table 3: a dry 1×10 is at least 3/4 by 9-1/4. Read the nominal and dressed sizes page before you assume a board at the store matches the label. The nominal tally for the two sticks you buy is 13.33 board feet. The board-foot calculator shows why that number is larger than the wood you actually get.

Cut list

Finished sizes. Thickness and width are the PS 20 minimum dressed dry sizes for a 1×10.
PartQtyThicknessWidthLength
Side23/49-1/436
Top, middle, and bottom shelves33/49-1/428-1/2
Back, 1/4 inch plywood11/43036

Outside width check: 3/4 + 28-1/2 + 3/4 = 30. Height check: the bottom shelf takes the first 3/4 inch, the top shelf takes the last 3/4 inch, and the middle shelf takes 3/4 inch between two equal openings. 36 − 2.25 = 33.75, and 33.75 / 2 = 16.875, which is 16-7/8. The middle shelf starts 17-5/8 inches up.

What to buy

  • Two 1×10 × 8 foot pine boards. Cutting plan, with a 1/8 inch kerf: one board yields 36, 28-1/2, and 28-1/2 (93-1/4 inches used). The other yields 36 and 28-1/2 (64-5/8 inches used) and about 31 inches of offcut.
  • 1/4 inch plywood, 30 by 36 inches. A half sheet is more than enough. A 2×4 foot handy panel is only 24 inches wide, so it is too narrow for a one-piece back.
  • Wood glue, about 24 wood screws at 1-1/2 inch, and 5/8 inch brads or screws no longer than 3/4 inch for the back.
  • Optional dividers: one 16-7/8 inch piece fits the offcut. Two dividers need another short 1×10. Set one in each opening, under the shelf above, if you want to break the span.

Build it

  1. 1
    Check the boards Buy two 8-foot 1×10 boards and a piece of 1/4 inch plywood at least 30 by 36 inches. The cuts below assume the PS 20 minimum dressed dry size, 3/4 by 9-1/4. Measure. If a side is thicker than 3/4, shorten every shelf by the extra thickness of both sides.
  2. 2
    Cut five boards Cut two sides at 36 inches and three shelves at 28-1/2 inches. The length is the finished length. The saw blade eats its own kerf, about 1/8 inch, out of the offcut, not out of the piece you are keeping.
  3. 3
    Mark both sides at once Clamp the two sides face to face so the marks match. Bottom shelf flush with the floor end. Top shelf flush with the top end. Middle shelf: bottom edge 17-5/8 inches up from the floor end. That leaves two openings of 16-7/8 inches.
  4. 4
    Drill, then glue Predrill four holes at each shelf end, countersunk from the outside face, or put pocket holes on the underside of the shelf so the screw heads hide. Use 1-1/2 inch wood screws. A 1-1/2 inch screw through the 3/4 inch side leaves 3/4 inch in the end of the shelf.
  5. 5
    Assemble and square Spread wood glue on each shelf end, seat the shelf on the line, and drive the screws. Measure the two diagonals of the front rectangle. If they differ, push the long diagonal until they match. Hold it there.
  6. 6
    Nail on the back Cut the back to 30 inches by 36 inches and fasten it while the diagonals still match. Use 5/8 inch brads, or screws no longer than 3/4 inch, so they stay inside the 3/4 inch sides. Space them about 6 inches apart on the sides and across each shelf.

Safety

Wear safety glasses. Wear hearing protection with a power saw, and a dust mask when you sand. Keep fingers out of the cut line and use a push stick on a table saw. Unplug a saw before you change the blade. Predrill pine and cedar so the screws don't split the board.

These are shop notes for a home project, not a substitute for the manual that came with your saw. OSHA's woodworking overview is the longer version for anyone cutting wood as a job.

Finish

Sand to 120 grit, then 180. Finish with a product labeled for indoor furniture, or leave the pine bare. Keep the case out of a damp garage if you leave it unfinished. Do not mount it to a wall from these instructions. A bookcase this size should stand against a wall, and a tall case should be anchored. This one is 36 inches, which is a low case, and the back still has to be on or the shelves will lean.

Questions

How wide is the finished bookshelf?

30 inches wide, 36 inches tall, and 9-1/4 inches deep. The depth is the width of a dressed 1×10. The 30 inch width is a 28-1/2 inch shelf plus two 3/4 inch sides.

Will a 28 inch pine shelf hold books?

It will hold paperbacks. A full row of large hardcovers can sag a 3/4 inch pine shelf over a 28-1/2 inch span. Add a vertical divider in each opening, or shorten the case, if that is what you own. This page does not quote a weight rating.

Where TimberTinker fits. A bookshelf is one of the parametric templates in the app, next to cabinets, tables, drawer boxes, and workbenches. The listing also names pocket screws and dados if you want a different joint than the butt joint on this page. TimberTinker: Woodworking 3D is free to download on the U.S. App Store. The listing says the first 3 projects are free, then Premium. On the U.S. listing checked November 19, 2026, the in-app purchases are named Unlimited Access at $5.99, Unlimited Access at $12.99, and timbertinker at $49.99. The listing does not say how long each purchase lasts. It does say the app uses real lumber sizes from 2×4s to 3/4 inch plywood, writes a cut list, and estimates cost by the board foot and by the sheet. Redraw this piece in the app and read its cut list as a second check. Measure the board in your hand before you cut. This page has not compared the app's output to these numbers.

Sources

Pages and prices were checked November 19, 2026. A store price can change, and a support page can be revised. The link is the record.